aglt spindles???????

128556 · Nov 17, 2011

ok guys iam lost i confused on what spindles will work for this? If anybody can give me a list of every spindle that will work that would be much appreciated thanks

kev · Nov 17, 2011

Frenchie · Nov 17, 2011

ive got two pairs from a 97 zrt for sale--not notched but could be for a little extra:wub:

128556 · Nov 17, 2011

Pm sent

Sent from my LS670 using Tapatalk

128556 · Nov 17, 2011

i did some more research and i am puzzled by tthis problem that i am having. My spindles are the stock ones that were on my 96 zrt 600 and they are the aluminum ones they should be fine according to a post on the aglt thread. But the issues that i am having is that the spindle will not line up with the new a arm.s i read on another older thread about some mounting tabs??????? i am not sure if this applies to me or not any help would be appreciated thanks a ton.

mttporter · Nov 17, 2011

Do you have the shock mounted? If so, it needs to be mounted upside down.
The middle tabs on the chasis that used to hold the 2 armed a arms needed to be removed so that the new traingle a arm would fit.

128556 · Nov 17, 2011

I do not have the shocks on at all just trying mockup. The top arm is back a little to far it seems like so it will not line up. Arms are off a 2002 cce. Will these tabs prevent the top arm from going on at all?

Sent from my LS670 using Tapatalk

kev · Nov 18, 2011

Are you having issues with both sides? I'm having that issue, but suspect it's more to do with bent A arms. I've never had an issue with which way the shock mounts though.

128556 · Nov 18, 2011

I am on the right side haven't started on the left side yet but all arms are straight

Sent from my LS670 using Tapatalk

kev · Nov 18, 2011

I would try the left side and see if you have the same problem. My problems are on the right side too. 2 different sets of arms too.

mttporter · Nov 18, 2011

The tabs that used to hold the split a arms need to be removed - I used a sawzall.
Then a spacer needs to be added at the front of the new triangle a arms ti fill the gap. Spacer must be towards the front of the sled to maintain the original geometry for steering and suspension.
You can't even mock it up with the tabs in place from the old split a arms.
I had to also drill a hole in the belly pan plastice to make room for the longer bolt to be inserted into upper a arm.

128556 · Nov 18, 2011

I will look for some tabs but my upper and lower arms bolt right up on the frame side.

Sent from my LS670 using Tapatalk

mdewkid · Nov 18, 2011

spindles

Maybe you could post some pics, then maybe some of the guys could chime in . this is my right side finally put together

128556 · Nov 18, 2011

I am going to try to get out there tonight and I will take some pics

Sent from my LS670 using Tapatalk

128556 · Nov 19, 2011

OK I think my bulkhead is bent anybody have some info on the best way to confirm this???? Thanks

Sent from my LS670 using Tapatalk

Guest · Nov 19, 2011

Here you go...

128556 · Nov 19, 2011

Thanks again for posting them dan

These are my arms how they look now

Sent from my LS670 using Tapatalk

Guest · Nov 19, 2011

After I have looked at the pictures, I have to say you have the wrong arms. The bottom one even looks funny. Not the right angle to me.

kev · Nov 19, 2011

Do you have the spacers at the front of the arm where it mounts to the bulkhead? I can't tell in the picture. Have you tried the left side yet? If the left side lines up, it will help determine if you have the right arms or another issue.

mttporter · Nov 19, 2011

It may be the wrong lower a arm mine are different than the ones in your picture - here is the link http://www.kenssportspolarisparts.c...PRO_(GREEN)_(S2003ZRHEPUSG)/A-ARM_ASSEMBLY/S2003ZRHEPUSG-2003-164/441640737-343
w/correct part#1703-028 A-ARM, LWR RH and 1703-029 A-ARM, LWR LH
and diagram showing what the correct arm looks like

128556 · Nov 19, 2011

I think u guys are on to something. I do believe the lower arms are not right. I ran a bunch of numbers and it appears the top arms are fine but the lowers are not Why would these not be right but the uppers are?

according to browns leisure world the part numbers for the arms that i have are
uppers 0703-939
lowers 1703-018 and 1703-019

Sent from my LS670 using Tapatalk

128556 · Nov 19, 2011

but on this thread the same arms that i have were used on the aglt conversion???? now i am really lost

http://www.arcticchat.com/forum/z-z...forum/z-zl-zr-zrt-tcat-ext/274103-aglt-long-travel-skid-mod-1996-zrt-600-a.html

kev · Nov 19, 2011

Sometimes it's just paint color that gives it a different part number.

128556 · Nov 20, 2011

OK I found the issue the right arm was twisted, put it on a jig to check it and it's pretty far off.. now to fix it and install. I will keep an update. Thanks to everyone who posted and again for Dan putting up my pics

Sent from my LS670 using Tapatalk

Guest · Nov 20, 2011

I tried to call you last night because the more I thought about it I figured one arm or the other was bent because the other one lined up perfect. Thats why I asked if you ever tried the other side.

kev · Nov 20, 2011

Just looked at another set last night and both lower arms have a specific twist to them. They do lot sit level on the ground, like I would have thought.

aglt spindles???????

Attachments

Attachments

Top Contributors this Month

Recommended Communities