Click to view attachmentClick to view attachment

I've stripped my ZR and made a list of parts. Let me know your interest's. All will be plus shipping from NY, 13159. I have a corporate UPS account and will ship with my discounts but US Postal will still be cheaper on some smaller stuff. I have pics of everything and will gladly email them to you.

Scott

Left & Right black belly pans with green side piece and vents - $75 ea
Front black nose cone with bumper and hood mount - $50
Black skid plate (couple splits but still good condition) - $10
Right & Left arms and spindles (complete for both sides) - $50 ea
Sno Pro clicker shocks with recent rebuild and green springs - $250 pair
Drive shaft (smooth outside and cogged inside wheels) - $75
Jack shaft - $50
Brake Rotor - $15
Primary clutch (@200 miles since new weight arm bushings) - $150
Secondary clutch (same milage since new rollers and washers) - $150
Sway bar setup (both sides & bar. Adjustable) - $50
All steering parts from post out to A arms with all tie rod ends and mounts) - $50
Wire Harness - $35
Console with key and wired for both twistlock and RCA helmet heater. Just plug in - $30
Stator with the Mag and pickup (whole assembly) - $200
Mikuni Flat slides with choke lever/cables & 360 mains (will change if you tell me what size you need) - $150
Voltage regulator - $15
Speedo drive with key shaft - $10
Intake manifold boots (like new. no cracks or splits) - $35 pair
K&N filter's with snow chargers cut to fit in the ZR - $40 pair
Airbox elimination mount (aluminum to mount fuel pump & petcock, CDI & coil) - $40
Fuel pump - $15
Oil pump - $15
Oil tank with sender - $15
Coolant tank with cap and both hoses - $15
Complete stock exhaust (Y pipe, Pipe, Can) - $150 SOLD
Coolant pipe (mounts to heads) with t-stat and coolant sensor - $20
Recoil with handle and fairly new rope - $20
Both front motor mounts with the rubber Bulkhead mounts and the metal cross bracket - $25
Clutch side motor mount with new ($200 miles) snubber - $25
Motor cases with both ends, water pump, oil drive & mag end (crank is sold) - $150
Heat exchangers - $25 pair
Hood with headlight housing and front hinge (couple small cracks and reinforced center hinge mount) - $150
Red hood screens - $25
Steering post with upper and lower mounts (will throw in new bushing)- $15
CDI & coil - $75
136 x 15 x 1-1/4 ripsaw fully clipped. great shape - $300
Custom highrise seat with large mouth tank with built in guage - $400
Custom tunnel extension with crossfire/Mcat rear light/bumper, tunnel supports foot grip plates - $200
2004 crossfire snopro complete skid with fox zero pro shocks and graphite hyfax (excelent condition) - $750

I think that about covers it. Feel free to email at scooterber@verizon.net or PM through the site.

Scooter

ttt

ttt

What kind of extension for the tunnel? Anymore pics of it and would you take any OBO???? Thanks! Also, were you selling the handguards/ mounts at all? (as seen from the pic)?

The extension is custom made. I actually cut the tunnel in half on the sled leaving the extension mounted. This way whoever ends up with it will see exactly how it's mounted and lining it up will be a breeze. The grip plates are also included with the extension basically because they're cut to go around the tunnel supports and no one else would have a use for them. I'll get you some pictures probably tomorrow so you can see in detail. If you don't mind, send me an email to scooterber@verizon.net . It'll be easier to send pic's directly than uploading each one. If you'd rather I'll just send them through here. As for the bars and mounts, I'm keeping all of that for the next sled, sorry.......

Scott